3M water filter vs TAPP Water comparison and review


Thinking about buying a filter and considering a 3M Aquapure water filter vs TAPP faucet water filter? Buying a water filter can be a difficult decision. In this article we will try to provide an objective comparison to guide you through the decision. 

3M offers a wide range of filters including under the sink, table top and for the fridge. For the purpose of this article we focus on the most purchased under the sink filter. Specifically Aqua-Pure AP-DWS1000 & AP-DWS1000 LF but the comparison is valid for most 3M filters sold globally.

TAPP Water also offers several variants of its filters and so for simplicity we are using TAPP 2 as the benchmark.

We compare the 6 most important aspects including simplicity to install and use, taste of the water, filter efficiency, flow rate, capacity and price.

Simplicity to install and use 3M water filters vs TAPP Water 

One of the biggest differences between water filters is where and how they are installed. Under the sink water filters like 3M have the advantage of being hidden but with this comes a much more challenging installation. TAPP Water filters are visible but much easier to install.

3M: Although 3M claims DIY this is really only a true claim if you’re a hobby plumber. The filters are difficult to install, usually require drilling a new hole for the faucet and even changing the cartridges once it’s installed can be difficult. Many people attempting to do the work themselves reported leakage issues after a few weeks of use.

TAPP Water: Pretty much anyone can install in less than 1 min without tools. In case it doesn’t fit straight away adapters are provided free of charge. TAPP filters have an on/off switch to change between filtered and unfiltered water.

Winner: TAPP 2 by far thanks to its simplicity 

Filtration efficiency of 3M water filters compare to TAPP Water

First of all this comparison is a bit more complicated and the relevancy of specific filtration depends on your local water quality. Both 3M and TAPP Water recommend that you check your local water quality before choosing a water filter. Generally for public tap water a high quality carbon block filter is more than enough.

3M: The under the sink 3M AquaPure filters generally filter everything activated carbon filters do including 80+ substances such as chlorine, pesticides, herbicides, etc but also heavy metals. Most of the filters have a 0.5 micron rating which provides a higher level of bacteria filtration but also reduces the flowrate (see below).

TAPP Water: The TAPP 2 5-stage filters 100+ substances including chlorine, pesticides, herbicides, heavy metals, pharmaceuticals, microplastics etc. In addition to this the proprietary inhibition technology vastly reduces limescale. TAPP 2 uses a 1-2 micron filter which is more than sufficient for chlorinated tap water. For non-potable tap water TAPP Water also offers TAPP Ultrafiltration with a 0.02 micron rating.

Winner: It’s a draw. Both 3M and TAPP Water offer similar type water filtration depending on what filter you choose. TAPP 2 offers the added advantage of limescale filtration.

Taste of the filtered water:

Although taste can be subjective we’ve found that it’s very consistent when it comes to tap water. With a high quality carbon block filter people can immediately taste the difference. 

3M: Based on our tests the 3M AquaPure efficiently a remove all the chlorine taste and some common metalic taste from iron rich tap water. Overall the filtered water tastes goos to great.

TAPP Water:Taste has always been one of our core pillars. From day one we’ve done blind tasting benchmarking different filters and bottled water. TAPP 2 almost always comes out at top. Many customers point out that the improvements in taste are almost magical.

Winner: Draw as both filters deliver great tasting tap water 

Flow-rate of 3M AquPure filters vs TAPP Water

This is one of the most important aspects of a good user experience. High flowrate means you can seamlessly fill up a glass of water, carafe, water kettle or coffee machine. Low water flow can be very annoying. The normal tap water flow without a filter is typically around 8-10 L/min.

3M: According to the specification the flowrate is 2.3 L/min and our tests confirmed this at around 2 L/min.

TAPP Water: The product is designed for a max flowrate of 4 L / min. With this it’s a small difference compared to unfiltered water.

Winner: TAPP 2 by TAPP Water with a wide margin

Filter capacity and replacements.

Another important aspect of water filters is how often you need to replace them, how to know when and how easy it is.

3M: The capacity of the 3M AquaPure filter is 3750 L per cartridge and the 2 cartridges should be replaced every 6 months. The latest version has an automatic shutoff after 6 months and capacity is reached. Although the system is called easy-replace it does require you to crawl under the sink, removing everything around the filter and then unscrew and screw the filters back in. 

TAPP Water: TAPP 2 cartridges have a capacity of 1200 L and should be replaced every 3 months. The MyTAPP service included with TAPP provides continuous updates on environmental impact, cost savings and more with a reminder when it’s time to change the cartridge. It takes less than 30s to make the switch.

Winner: TAPP Water thanks the reminders and easy replacement.


System including 4 cartridges: 900 MOP

Replacement cartridges: 1424 MOP every 6 months